Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.cncmachining-cn.com/wp-content/uploads/2020/08) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1922

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.cncmachining-cn.com/wp-content/uploads/2020) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1933

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.cncmachining-cn.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1933

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.cncmachining-cn.com/wp-content) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1933

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.cncmachining-cn.com) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1933

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1933

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1933

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/cncmachining-cn.com/:/tmp/:/proc/) in /www/wwwroot/cncmachining-cn.com/wp-includes/functions.php on line 1933
数控中心加工时如何保证其垂直度或平行度?-数控中心加工时如何保证其垂直度或平行度?-CNC武林

数控中心加工时如何保证其垂直度或平行度?

  东莞市鸿奥精密机械有限公司市场经理李生(16620722077 微信同号)在线解答,在这里我们先不考虑数控机床本身的一些干扰因素,那就只有两个可控的因素:装夹和切削

一定要正确的装夹,贴实压稳夹紧力要适当,要做到你认为松开压板后工件不会回弹虎钳的装夹。这里就不在多说了,装夹适当,不多不少,基本的操作,正常的铣工都会。切削余量 ,转速和进给要配合到位,余量留多,对精铣出的效果不好,余量要适当。转速这块具体根据所用刀具来修改,这方面也不累述,大家注意好这几点就好。

如有对机床有选购意向的不妨看看我的另两篇文章:“买机床要考虑哪些因素,怎样才能买到好的数控”“选购数控机床必须遵循的原则和注意问题有哪些?”干货分享,保证你受益良多。

  最后祝各位数控中心的朋友享受工作,热爱生命,生活幸福!

 

本文由来源 www.cncmachining-cn.com,由 cnc加工 整理编辑,其版权均为 www.cncmachining-cn.com 所有,文章内容系作者个人观点,不代表 CNC武林 对观点赞同或支持。如需转载,请注明文章来源。

发表评论